1、在推送木材时，要根据多片锯锯机的速度进行推送，以免过快或者过慢导致木材反弹从而受伤；

2、对于新手操作员，应安排熟练的操作员手把手教学，先熟悉后作业，严格安装操作准则来进行作业；

3、拆装多片锯锯片时应关闭电源，并关上电源盖，以免误触电源按钮；

4、多片锯锯片不平时应及时反映，并且及时更换锯片；

不管是圆木多片锯还是方木多片锯，两者都属于大型加工设备，只有未雨绸缪才能更好地预防意外的发生。

如何确保原木多片锯的铝型材高精？

1、设备状况精捷，主轴轴承无形变、震荡，轴径尺寸公差为h7，应用时要设备维护管理罩；

2、作业者应具备实际操作所必需的基本常识并配置维护保养目镜，留心优先结及衣袖，不可以带胶手套，长直发要戴工作帽； 

3、查验锯齿状有没有损坏、坠落，反常现象损坏及锯盘坎坷、误会等反常现象现象； 

4、机器设备时要保证锯片翻转方位与设备主轴轴承翻转方位一起； 

5、机器设备时要招认选定锯片适合于被钻削原材料的转速比、切削速度（按原文中强烈推荐，先选切削用量、每齿切削速度再按锯片直徑齿数结转转速比和每分切削速度）； 

6、每一次机器设备法兰片必须保证法兰片表面平整清洁、互相平行面与中心线竖直、尺寸要一起、法兰片小直徑是锯片直徑的1/3，密封圈应竖直； 

7、机器设备时锯片要高于板才高宽比少相当于锯齿状高宽比； 

8、横截时、一起割开的齿少3齿，不然锯片会晃动； 

9、应用时被割开原材料应固定不动，发觉动态性和震荡反常现象、断开面不光滑、坎坷时要连续工作，立即查验，故障检测。 

10、当锯片不锐利及断开面不光滑时，必须立即开展再碾磨，再碾磨时不可以修改原视角，必须给值得信赖的专业生产厂家开展刃磨； 

11、另一方木多片锯锯片包裝和拆包裝的实际操作系统进程中（如全自动包装机）必须十分谨小慎微、刃口锐利非常简单组成伤害； 

12、运送锯片时会必需应用适合的包裝避免毁坏。

1. When pushing wood, it should be pushed according to the speed of the multi blade saw to avoid too fast or too slow leading to wood rebound and injury;

2. For novice operators, skilled operator hand teaching should be arranged, first familiar with the operation, and then strictly install the operation rules to carry out the operation;

3. Turn off the power supply and close the power cover when disassembling the multi blade saw blade, so as not to touch the power button by mistake;

4. In case of any irregularity of multi blade saw blade, timely report and replace the saw blade;

Both of them belong to large-scale processing equipment, so we can prevent accidents better if we take precautions.

How to ensure the high precision of the aluminum profile of the log multi blade saw?

1. The equipment is in good condition, the main shaft bearing changes and vibrates intangibly, the tolerance of shaft diameter is H7, and the equipment maintenance and management cover is required during application;

2. Operators shall have the basic knowledge necessary for practical operation and shall be equipped with maintenance goggles, pay attention to the bow tie and sleeves, do not wear rubber gloves, and wear work caps for long straight hair;

3. Check whether the saw tooth is damaged, falling, abnormal phenomenon damage, rough saw disk, misunderstanding and other abnormal phenomena;

4. Ensure that the turning direction of saw blade and the turning direction of main shaft bearing of the equipment are the same;

5. When selecting the machine and equipment, it is necessary to identify the rotation speed ratio and cutting speed of the saw blade suitable for the raw materials to be drilled (as strongly recommended in the original text, first select the cutting amount and cutting speed of each tooth, then carry forward the rotation speed ratio and cutting speed of each minute according to the number of teeth in the saw blade diameter);

6. The flange of each machine and equipment must ensure that the surface of the flange is flat and clean, parallel to each other and the center line is vertical, the size should be together, the small diameter of the flange is 1 / 3 of the saw blade diameter, and the sealing ring should be vertical;

7. When the machine is equipped, the height width ratio of the saw blade should be higher than that of the plate;

8. When cross cutting, the teeth cut together are less than 3 teeth, otherwise the saw blade will shake;

9. The cut raw materials shall be fixed during application, and continuous operation shall be carried out in case of abnormal dynamic and vibration, unsmooth and rough breaking surface, immediate inspection and fault detection.

10. When the saw blade is not sharp and the cut-off surface is not smooth, re grinding must be carried out immediately. During re grinding, the original angle of view cannot be modified, and the blade grinding must be carried out for the reliable professional manufacturer;

11. On the other hand, in the process of packaging and unpacking of multi saw blades, the actual operating system (such as full-automatic packaging machine) must be very cautious, sharp edge and very simple to constitute damage;

12. When transporting saw blades, it is necessary to use suitable packaging to avoid damage.